• cock ring

    1404580301
    christo [sign in to see picture]
    • Rank: Captain
    • Posts: 1
    • Joined: 22 Mar 2013

    Why do i struggle to put a cock and ball ring on cant seem to get balls in

    1404580659

    [suspended user]

    suspended user
    • Rank: Field Marshall
    • Posts: 2993
    • Joined: 25 Apr 2013

    Are you using lube? It really helps. :)

    1404583743
    BigBikeGuy [sign in to see picture]
    • Rank: General
    • Posts: 459
    • Joined: 16 May 2008

    Try one of these, without a doubt the best cock ring I've ever used...

    Good shout with the lube as well Lollipop, always lube up..

    http://www.lovehoney.co.uk/product.cfm?p=2589

    1404584083
    GTID [sign in to see picture]
    • Rank: Lieutenant
    • Posts: 23
    • Joined: 12 Jun 2012

    Lube is essential for me, can be quite painful without!

    1404586286
    Young and fun95 [sign in to see picture]
    • Rank: Field Marshall
    • Posts: 2748
    • Joined: 6 Jun 2014

    I open it up with my hands inside in and cup my mans balls then slide the ring off my hand I couldn't know how else to do it

    1404589180
    JuicyJ89 [sign in to see picture]
    • Rank: General
    • Posts: 963
    • Joined: 10 Nov 2008

    my hubby uses this http://www.lovehoney.co.uk/product.cfm?p=28652

    pulls the toggle bit all the way to the end (leave a little bit of the ring poking out or you will never get it back on if the toggle comes off) and a little bit of lube. Puts penis through and stretches over balls and then tightens.

    1404591182
    j&lxxxx [sign in to see picture]
    • Rank: Brigadier
    • Posts: 201
    • Joined: 13 May 2012

    Is it a metal ring? If so I find best way is plenty of lube, put cock in first, then pull through loose sack, and then gently squeeze balls through one at a time. Sorry if to much info.

    1404635660
    Young and fun95 [sign in to see picture]
    • Rank: Field Marshall
    • Posts: 2748
    • Joined: 6 Jun 2014

    Metal cock rings or any kind of fixed ring should be put on when flaccid. Put testicles in then push willy through

    1404640442
    Sum Sub [sign in to see picture]
    • Rank: Field Marshall
    • Posts: 4218
    • Joined: 4 Dec 2012

    There's a technique which I have learned from the ancient Japanese art of cockerami.

    What you do is pop your old chap and his two baggy friends into the end of an (old) stocking, think much like genitals robbing a bank.
    then you pop your balls through the ring and the penis - still in the stocking.
    As advised above, please complete this task when in a non-aroused state.

    Once you're happy with the position, then act like a magician and whip that stocking off leaving everything else where it was.

    by jingo one enringed old chap.

    then lube up if it feels tight, or keep the stocking on for a different sensation.

    1404643137
    Quiet ones are worse! [sign in to see picture]
    • Rank: General
    • Posts: 900
    • Joined: 24 Jun 2012

    It's a bit of an art, make sure you're nice and warm, say after a bath and everything is more baggy, yes lube is good but I've found with it your fingers are TOO slippery to help, so without any at the start I do this

    Place to one side a bit and gently push one ball through leaving the other still to the upper other side, give the loose skin of the one through the ring a bit of a pull, to make, as much skin through the ring as you can, now tease/push the other ball through give the whole lot a tug, gently.

    Now stick some lube on your bit and push/coax/pull it through holding the ring at the same time, once you've done that grab a hold of everything just in front of the ring then push the ring back with your other hand as far as it will go. It seems much easier with my metal rings than the "sticky" silicone one, don't give up just take practice, if you think it will be a bit of a mood killer, all that messing around, put it on a hour or so before, I wear my metal one for days with no harm.

    Post a reply to this thread

    Please sign in to post messages to the forum.